小型傳感器100
聲明：您必須遵守我們的協議，如果您下載了該資源行為將被視為對《電天下賬號管理規范》全部內容的認可，本網站資源來自原創，僅供用于學習和交流，請勿用于商業用途。如有侵權、不妥之處，請舉報本資源，我們將及時審核處理！
小型傳感器100
小型傳感器100
文本預覽
MiniSense 100 Vibration Sensor
The MiniSense 100 is a low-cost cantilever-type vibration produces a linear output governed by the "baseline"
sensor loaded by a mass to offer high sensitivity at low sensitivity. The sensitivity at resonance is significantly
frequencies. Pins are designed for easy installation and higher. Impacts containing high-frequency components
are solderable. Horizontal and vertical mounting options will excite the resonance fre-quency, as shown in the plot
are offered. The active sensor area is shielded for above (response of MiniSense 100 to a single half-sine
improved RFI/EMI rejection. Rugged, flexible PVDF impulse at 100 Hz, of amplitude 0.9 g). The ability of the
sensing element withstands high shock overload. Sensor sensor to detect low frequency motion is strongly
has excellent linearity and dynamic range, and may be influenced by the external
used for detecting either continuous vibration or impacts. electrical circuit, as
described below
The mass may be modified to obtain alternative frequency (see "Electrical
response and sensitivity selection (consult factory). Description").
The MiniSense 100 acts as a cantilever-beam
accelerometer. When the beam is mounted horizontally,
acceleration in the vertical plane creates bending in the
beam, due to the inertia of the mass at the tip of the beam.
Strain in the beam creates a piezoelectric response, which
may be detected as a charge or voltage output across the
electrodes of the sensor.
The sensor may be used to detect either continuous or
impulsive vibration or impacts. For excitation frequencies
below the resonant frequency of the sensor, the device
Outline Mechanical Dimensions
Electrical Description
The Minisense 100 behaves electrically as an "active" capacitor: it may be modelled as a perfect voltage source (voltage
proportional to applied acceleration) in series with the quoted device capacitance. Any external input or load resistance
will form a high-pass filter, with a roll-off frequency as tabulated above, or calculated from the formula f(c) = 1/(2 RC).
The impedance of the sensor is approximately 650 M ohm at 1 Hz. The active sensor element is electrically shielded,
although care should be taken in the PCB design to keep unshielded traces as short as possible.
Description Part Number
MiniSense 100 (Horizontal) 1005939-1
MiniSense 100 (Vertical) 1005940-1
Please contact factory for custom part quotations and volume pricing.
Dec. 8, 03
MSI Sensors www.piezofilm.com (757) 766-4474 Fax (757) 766-3979
2
The MiniSense 100 is a low-cost cantilever-type vibration produces a linear output governed by the "baseline"
sensor loaded by a mass to offer high sensitivity at low sensitivity. The sensitivity at resonance is significantly
frequencies. Pins are designed for easy installation and higher. Impacts containing high-frequency components
are solderable. Horizontal and vertical mounting options will excite the resonance fre-quency, as shown in the plot
are offered. The active sensor area is shielded for above (response of MiniSense 100 to a single half-sine
improved RFI/EMI rejection. Rugged, flexible PVDF impulse at 100 Hz, of amplitude 0.9 g). The ability of the
sensing element withstands high shock overload. Sensor sensor to detect low frequency motion is strongly
has excellent linearity and dynamic range, and may be influenced by the external
used for detecting either continuous vibration or impacts. electrical circuit, as
described below
The mass may be modified to obtain alternative frequency (see "Electrical
response and sensitivity selection (consult factory). Description").
The MiniSense 100 acts as a cantilever-beam
accelerometer. When the beam is mounted horizontally,
acceleration in the vertical plane creates bending in the
beam, due to the inertia of the mass at the tip of the beam.
Strain in the beam creates a piezoelectric response, which
may be detected as a charge or voltage output across the
electrodes of the sensor.
The sensor may be used to detect either continuous or
impulsive vibration or impacts. For excitation frequencies
below the resonant frequency of the sensor, the device
Outline Mechanical Dimensions
Electrical Description
The Minisense 100 behaves electrically as an "active" capacitor: it may be modelled as a perfect voltage source (voltage
proportional to applied acceleration) in series with the quoted device capacitance. Any external input or load resistance
will form a high-pass filter, with a roll-off frequency as tabulated above, or calculated from the formula f(c) = 1/(2 RC).
The impedance of the sensor is approximately 650 M ohm at 1 Hz. The active sensor element is electrically shielded,
although care should be taken in the PCB design to keep unshielded traces as short as possible.
Description Part Number
MiniSense 100 (Horizontal) 1005939-1
MiniSense 100 (Vertical) 1005940-1
Please contact factory for custom part quotations and volume pricing.
Dec. 8, 03
MSI Sensors www.piezofilm.com (757) 766-4474 Fax (757) 766-3979
2
AIGC您好，關于您的問題"小型傳感器100"，我理解您可能在詢問一種特定類型的傳感器，它可能是指尺寸小巧、功耗低或者性能適用于小型設備的電子元件。這種傳感器通常用于監測環境參數（如溫度、濕度、壓力、光照等）、工業生產過程中的數據采集，或者是物聯網(IoT)設備中的信號感應。
"100"可能是指型號、系列編號或者是傳感器的某個規格參數，比如測量范圍、精度等級或者是每分鐘采樣次數等。如果您需要具體的產品信息、價格、安裝指南或技術支持，請?zhí)峁└嘈畔ⅲ視M我所能幫助您。如果只是想了解這類傳感器的一般特性，小型傳感器通常具有體積小、易集成、能耗低的優勢，非常適合空間受限的應用場景。
